Brocade FastIron Ethernet Switch Layer 3 Routing Configura Manual de usuario Pagina 217
- Pagina / 672
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Syntax: show ipv6 dhcp-relay interface interfacetype
The interface type is interface type such as ethernet, POS, or VE and the specific port number.
Table 48 describes the fields from the output of the show ipv6 dhcp-relay interface command.
Output from the show ipv6 dhcp-relay interface commandTABLE 48
Field Description
Destinations The DHCPv6 relay destination configured on the interface.
• Destination : The configured destination IPv6 address.
• OutgoingInterface : The interface on which packet will be relayed if the destination relay
address is link local or multicast.
Options The current information about DHCPv6 relay options for the interface.
• Interface-Id : The interface ID option indicating if the option is used or not.
• Remote-Id : The remote ID option indicating if the option is used or not.
Prefix Delegation
Notification
This current information about the DHCPv6 Prefix Delegation for the interface.
• Interface: The name of the interface.
• Current - The number of delegated prefixes currently learned on the interface.
• Maximum - The maximum number of delegated prefixes that can be learned on the
interface.
• AdminDistance - The administrative distance used for prefixes learned on the specific
interface when added to IPv6 Static Route table.
Clearing the DHCPv6 delegated prefixes
To clear the DHCPv6 delegated prefixes for specific VRFs, use the clear ipv6 dhcp-relay delegated-
prefixes command at the privilege level.
device# clear ipv6 dhcp-relay delegated-prefixes vrf VRF1
Syntax: clear ipv6 dhcp-relay delegated-prefixes { vrf vrf-name } { X:X::X:X/M | all | interface
interface-id }
The vrfvrf-name parameter is used to clear the DHCPv6 delegated prefixes for a specific VRF. If this
parameter is not provided, then the information for the default VRF is cleared.
The X:X::X:X/M parameter is used to clear the specified delegated prefix and remove the corresponding
route permanently from the router.
The all parameter is used to clear all the delegated prefixes and remove the corresponding routes
permanently from the router for the VRF.
The interfaceinterface-id parameter is used to clear all the delegated prefixes and remove the
corresponding routes permanently from the router for the specified outgoing interface.
Clearing the DHCPv6 packet counters
To clear all DHCPv6 packet counters, use the clear ipv6 dhcp-relay statistics command at the
privilege level.
device# clear ipv6 dhcp-relay statistics
Clearing the DHCPv6 delegated prefixes
FastIron Ethernet Switch Layer 3 Routing Configuration Guide 217
53-1003087-04
- FastIron Ethernet Switch 1
- Layer 3 Routing 1
- Contents 3
- 53-1003087-04 10
- Document conventions 15
- Notes, cautions, and warnings 16
- Brocade resources 17
- Document feedback 18
- About This Document 19
- Basic IP configuration 22
- IP configuration overview 23
- Layer 3 switches 24
- Layer 2 switches 24
- ARP cache 26
- Static ARP table 26
- IP route table 27
- IP forwarding cache 27
- IP route exchange protocols 28
- IP multicast protocols 29
- ACLs and IP access policies 29
- Configuring IP addresses 38
- Deleting an IP address 41
- Configuration example 42
- Configuring DNS resolver 43
- Defining DNS server addresses 44
- Defining a domain list 44
- Configuring packet parameters 45
- Changing the MTU 46
- Changing the router ID 48
- Telnet packets 50
- TACACS/TACACS+ packets 51
- RADIUS packets 51
- TFTP packets 51
- Syslog packets 52
- SNTP packets 52
- SSH packets 52
- ARP parameter configuration 53
- Rate limiting ARP packets 54
- Changing the ARP aging period 55
- Enabling proxy ARP 55
- Creating static ARP entries 56
- ARP Packet Validation 58
- Ingress ARP packet priority 59
- Disabling ICMP messages 62
- Static routes configuration 64
- Static IP route parameters 65
- Configuring a static IP route 66
- Naming a static IP route 68
- Configuring IP load sharing 74
- Path cost 75
- How IP load sharing works 76
- IRDP parameters 77
- Enabling IRDP globally 78
- Disabling RARP 80
- Creating static RARP entries 80
- DHCP Server 85
- DHCP Option 82 support 86
- DHCP Server options 86
- Default DHCP server settings 88
- DHCP server CLI commands 88
- Removing DHCP leases 90
- Enabling DHCP Server 90
- Creating an address pool 91
- Configuring the TFTP server 94
- DHCP Log messages 104
- Defining a DNS entry 106
- Changing the TTL threshold 107
- DHCP Assist configuration 108
- How DHCP Assist works 109
- IP Configuration 110
- Configuring DHCP Assist 111
- IPv4 GRE tunnel overview 112
- Creating a tunnel interface 119
- Clearing GRE statistics 131
- Displaying ARP entries 136
- Displaying the IP route table 140
- Clearing IP routes 143
- Syntax: show ip traffic 148
- Disabling IP checksum check 151
- Layer 3 Routing Protocols 153
- Adding a static IP route 154
- Static route recursive lookup 156
- Adding a static ARP entry 157
- Layer 3 configuration notes 158
- Switches 163
- IPv6 addressing overview 165
- IPv6 address types 166
- IPv6 CLI command support 168
- Enabling IPv6 routing 172
- FE48:4672:/64 173
- Configuring SNMP V3 over IPv6 177
- Secure Shell, SCP, and IPv6 177
- IPv6 Telnet 177
- IPv6 traceroute 178
- Defining an IPv6 DNS entry 179
- Pinging an IPv6 address 179
- Contact: 180
- Neighbor redirect messages 185
- IPv6 MTU 190
- Clearing the IPv6 cache 194
- Displaying local IPv6 routers 201
- Syntax: show ipv6 traffic 205
- DHCP relay agent for IPv6 209
- RIP feature support 219
- RIP Overview 219
- RIP parameters and defaults 220
- Configuring RIP parameters 222
- Configuring metric parameters 223
- Configuring redistribution 224
- Enabling redistribution 225
- Setting RIP timers 229
- Displaying RIP Information 230
- Metric-offset, Outbound 0 231
- RIPng feature support 233
- RIPng Overview 233
- Configuring RIPng 234
- Configuring RIPng timers 235
- Displaying RIPng information 239
- OSPFv2 feature support 243
- OSPF overview 244
- OSPF point-to-point links 246
- OSPF graceful restart 252
- Configuring OSPF 254
- OSPF parameters 255
- Enable OSPF on the device 256
- Assign OSPF areas 256
- Assign a totally stubby area 257
- Configuring an NSSA 258
- Modify interface defaults 262
- Assign virtual links 266
- Define redistribution filters 271
- Enable route redistribution 273
- OSPF non-stop routing 279
- LSA delayed acknowledging 280
- LSA syncing and packing 280
- Standby module operations 281
- Enabling and disabling NSR 282
- Disabling configuration 282
- OSPF distribute list 283
- Examples 284
- Modify SPF timers 286
- Modify OSPF traps generated 288
- Modify exit overflow interval 289
- Displaying OSPF information 295
- Displaying OSPF trap status 311
- Clearing OSPF neighbors 314
- Clearing OSPF information 316
- OSPFv3 feature support 317
- OSPFv3 overview 318
- Configuring OSPFv3 319
- Assigning OSPFv3 areas 320
- Specifying a network type 325
- Configuring virtual links 326
- Filtering OSPFv3 routes 332
- IPsec for OSPFv3 340
- Configuring IPsec for OSPFv3 340
- General considerations 341
- Configuring IPsec for an area 344
- Clearing IPsec statistics 346
- Displaying OSPFv3 information 348
- IPsec examples 372
- Showing IPsec policy 373
- Showing IPsec statistics 374
- Changing a key 378
- OSPFv3 clear commands 379
- Clearing OSPFv3 data in a VRF 380
- Clearing OSPFv3 neighbors 380
- Clearing OSPFv3 counters 381
- Configuring BGP4 (IPv4) 383
- BGP4 overview 385
- BGP4 message types 388
- Grouping of RIB-out peers 389
- Implementation of BGP4 390
- BGP4 restart 390
- BGP4 neighbor local AS 392
- Disabling BGP4 394
- BGP4 parameters 395
- Memory considerations 397
- Enabling BGP4 on the device 398
- Changing the device ID 398
- Setting the local AS number 399
- Adding a loopback interface 400
- Adding BGP4 neighbors 400
- Encryption example 406
- Adding a BGP4 peer group 408
- Configuring a peer group 409
- Enabling next-hop recursion 417
- Support for RFC 4456 425
- Configuring confederations 426
- Commands for device A 428
- Commands for device B 428
- Commands for device C 428
- Commands for device D 428
- Configuring BGP4 restart 429
- BGP4 null0 routing 431
- Configuration examples 432
- Redistributing RIP routes 435
- Redistributing static routes 436
- Redistributing IBGP routes 436
- Filtering 437
- Using regular expressions 438
- BGP4 filtering communities 440
- Defining a community ACL 441
- Defining route maps 443
- Match examples using ACLs 445
- Matching based on interface 448
- Sending and receiving ORFs 452
- Enabling AS4 numbers 454
- Global AS4 configuration 455
- AS4 notation 457
- BGP4 AS4 attribute errors 458
- Generating traps for BGP4 464
- Configuring BGP4 464
- BGP route reflector 466
- BGP4 max-as error messages 471
- Originating the default route 471
- Dynamic route filter update 475
- Filter update delay and BGP 476
- Displaying BGP4 information 477
- Displaying advertised routes 491
- Displaying the best routes 492
- Displaying route details 499
- Displaying AS4 details 506
- Attribute entries 513
- Running configuration 514
- Using soft reconfiguration 517
- Dynamically refreshing routes 520
- Clearing traffic counters 523
- Clearing diagnostic buffers 523
- Configuring BGP4+ 525
- Enabling BGP4+ 527
- Adding BGP4+ neighbor 528
- Configuring a route map 529
- Creating a BGP4+ peer group 530
- Importing routes into BGP4+ 532
- Using route maps 534
- Clearing BGP4+ information 537
- Displaying BGP4+ information 541
- Total number of BGP Routes: 4 547
- Displaying BGP4+ summary 580
- VRRP and VRRP-E 585
- Overview 586
- VRRP and VRRP-E overview 586
- Virtual router ID 588
- Virtual router MAC address 588
- Virtual router IP address 589
- Master negotiation 589
- Hello messages 590
- VRRP-E overview 591
- ARP behavior with VRRP-E 593
- Comparison of VRRP and VRRP-E 594
- VRRP and VRRP-E parameters 595
- Configuration rules for VRRP 599
- Configuring IPv4 VRRP-E 604
- Configuring IPv6 VRRP-E 604
- Configuring Switch 1 606
- VRRP syntax 606
- VRRP-E syntax 606
- VRRP router type 607
- Hello interval configuration 609
- Dead interval configuration 610
- Track port configuration 611
- Track priority configuration 611
- Backup preempt configuration 612
- Changing the timer scale 612
- VRRP-E slow start timer 613
- Displaying statistics 627
- VRRP example 632
- VRRP-E example 633
- Configuring Multi-VRF 635
- Multi-VRF Overview 637
- Configuring VRF instances 642
- Removing a Multi-VRF instance 644
- Configuring Management VRFs 645
- SNMP server 646
- SNMP trap generator 646
- SSH server 646
- Telnet client 646
- RADIUS client 647
- TACACS+ client 647
- Configuration notes 649
- Proxy ARP and Local Proxy ARP 653
- ARP rate-limiting 653
- Assigning loopback interfaces 655
- Multi-VRF Show commands 655
- Step 2: Configuring VRFs 660
- Layer 3 Routing Commands 663
Relacionado con productos y manuales para Accesorios De Computador Brocade FastIron Ethernet Switch Layer 3 Routing Configura
Accesorios De Computador Brocade Network OS Message Reference v4.1.1 Manual de usuario
(478 paginas)
(478 paginas)
Accesorios De Computador Brocade Mid-Mount Rack Kit (Switch) Installation Procedure Manual de usuario
(10 paginas)
(10 paginas)
Accesorios De Computador Brocade Flush Mount Rack Kit Installation Procedure (Suppo Manual de usuario
(10 paginas)
(10 paginas)
Accesorios De Computador Brocade Network OS NETCONF Operations Guide v4.1.1 Manual de usuario
(622 paginas)
(622 paginas)
Accesorios De Computador Brocade VDX 6710-54 Hardware Reference Manual Manual de usuario
(72 paginas)
(72 paginas)
Accesorios De Computador Brocade VDX 6730 QuickStart Guide (Supporting VDX 6730-32 Manual de usuario
(12 paginas)
(12 paginas)
Accesorios De Computador Brocade VDX 8770-8 Two-Post Flush and Mid-Mount Rack Kit I Manual de usuario
(8 paginas)
(8 paginas)
Accesorios De Computador Brocade VDX 6730 Hardware Reference Manual (Supporting VDX Manual de usuario
(90 paginas)
(90 paginas)
Accesorios De Computador Brocade VDX 8770-8 Four-Post Flush and Recessed Mount Rack Manual de usuario
(10 paginas)
(10 paginas)
Accesorios De Computador Brocade VDX 8770-4 Two-Post Flush and Mid-Mount Rack Kit I Manual de usuario
(10 paginas)
(10 paginas)
Accesorios De Computador Brocade VDX 8770-8 Hardware Reference Manual Manual de usuario
(136 paginas)
(136 paginas)
Accesorios De Computador Brocade VDX 8770-4 Four-Post Flush Mount Rack Kit Installa Manual de usuario
(8 paginas)
(8 paginas)
Accesorios De Computador Brocade Network OS Administrator’s Guide v4.1.1 Manual de usuario
(748 paginas)
(748 paginas)
Accesorios De Computador Brocade VDX 8770-4 Four-Post Flush and Recessed Mount Inta Manual de usuario
(24 paginas)
(24 paginas)
Accesorios De Computador Brocade VDX 8770-4 Hardware Reference Manual Manual de usuario
(132 paginas)
(132 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales