Brocade Multi-Service IronWare Multicast Configuration Gui Manual de usuario Pagina 56
- Pagina / 216
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
44 Multi-Service IronWare Multicast Configuration Guide
53-1003032-02
PIM Sparse
1
Syntax: [no] ip pim border
Configuring BSRs
In addition to the global and interface parameters described in the previous sections, you need to
identify an interface on at least one device as a candidate PIM Sparse Bootstrap router (BSR) and
candidate PIM Sparse Rendezvous Point (RP).
NOTE
It is possible to configure the device as only a candidate BSR or RP, but it is recommended that you
configure the same interface on the same device as both a BSR and an RP.
This section describes how to configure BSRs. Refer to “Configuring RPs” for instructions on how to
configure RPs.
To configure the device as a candidate BSR, enter commands such as the following.
Brocade(config)# router pim
Brocade(config-pim-router)# bsr-candidate ethernet 2/2 30 255
BSR address: 207.95.7.1, hash mask length: 30, priority: 255
These commands configure the PIM Sparse interface on port 2/2 as a BSR candidate, with a hash
mask length of 30 and a priority of 255. The information shown in italics above is displayed by the
CLI after you enter the candidate BSR configuration command.
Syntax: [no] bsr-candidate ethernet slot/portnum | loopback num | tunnel num | ve num
hash-mask-length [priority]
The ethernet slot/portnum | loopback num | ve num parameters specify the interface. The device
will advertise the IP address of the specified interface as a candidate BSR.
• Enter ethernet slot/portnum for a physical interface (port).
• Enter ve num for a virtual interface.
• Enter loopback num for a loopback interface.
• Enter tunnel num for a GRE tunnel interface to be configured. The GRE tunnel interface is
enabled under the router PIM configuration.
The hash-mask-length parameter specifies the number of bits in a group address that are
significant when calculating the group-to-RP mapping. You can specify a value from 1–32.
NOTE
it is recommended that you specify 30 for IP version 4 (IPv4) networks.
The priority specifies the BSR priority. You can specify a value from 0 – 255. When the election
process for BSR takes place, the candidate BSR with the highest priority becomes the BSR. The
default is 0.
Configuring RPs
Enter a command such as the following to configure the device as a candidate RP.
Brocade(config-pim-router)# rp-candidate ethernet 2/2
Syntax: [no] rp-candidate ethernet slot/portnum | loopback num | tunnel num | ve num
The ethernet slot/portnum | loopback num | ve num parameters specify the interface. The device
will advertise the IP address of the specified interface as a candidate RP.
• Enter ethernet slot/portnum for a physical interface (port).
- Multi-Service IronWare 1
- Document History 2
- Contents 3
- About This Document 7
- Supported software 8
- Document conventions 9
- Notice to the reader 10
- Related publications 10
- In this chapter 11
- Overview of IP multicasting 15
- VRF CAM entries 18
- Mtrace overview 20
- Mtrace components 21
- Configuring mtrace 22
- System max parameter changes 23
- Multicast non-stop routing 25
- IP multicast boundaries 28
- FIGURE 2 LSP path topology 30
- Limitations 31
- Enabling RPF shortcut feature 31
- Multicast ECMP support 32
- Limitations and prerequisites 34
- Enabling Multicast ECMP 35
- Enabling Rebalance 35
- PIM Dense 36
- Grafts to a multicast tree 39
- PIM DM versions 39
- Configuring PIM DM 40
- Modifying the TTL threshold 44
- Multicast PIM neighbor filter 50
- Limitation and prerequisites 51
- PIM Sparse 52
- PIM Sparse device types 53
- • Disables PIM or DVMRP 55
- Configuring RPs 56
- ACL based RP assignment 58
- Displaying the static RP 59
- Brocade(config)# router pim 62
- PIM multinet 63
- Displaying PIM counters 80
- • Group address: 232.1.0.95 82
- • RP address: 206.251.17.41 82
- Source Active caching 83
- Configuring MSDP 83
- Disabling an MSDP peer 84
- Displaying MSDP information 88
- Syntax: show ip msdp peer 89
- MSDP peer information 89
- Displaying MSDP RPF-Peer 93
- Displaying MSDP Peer 93
- Displaying MSDP VRF RPF-Peer 93
- Clearing MSDP information 94
- Configuring MSDP mesh groups 95
- Configuring MSDP mesh group 96
- MSDP Anycast RP 97
- RP 1 configuration 99
- RP 2 configuration 99
- MSDP Anycast RP 100
- PIMR1 configuration 100
- PIMR2 configuration 100
- PIM Anycast RP 101
- Example 102
- DVMRP overview 103
- Pruning a multicast tree 104
- Configuring DVMRP 105
- Brocade(config)# router dvmrp 106
- Brocade(config-dvmrp-router)# 106
- Brocade(config)# int e 3/1 106
- Modifying neighbor timeout 107
- Modifying route expires time 107
- Modifying route discard time 107
- Modifying prune age 107
- Modifying probe interval 108
- Modifying report interval 108
- Modifying trigger interval 108
- Modifying default route 108
- Displaying DVMRP information 109
- • DVMRP neighbor information 110
- • Ethernet 111
- • Disabled 111
- • Enabled 111
- Field Description 112
- This field... Displays 113
- 53-1003032-02 118
- Brocade(config)# vrf vpn1 119
- Brocade(config)# write memory 120
- Default IGMP version 121
- Creating a static IGMP group 124
- Setting the query interval 124
- Displaying IGMPv3 information 125
- This field Displays 126
- Displaying static IGMP groups 127
- Source-specific multicast 130
- Configuration Considerations 131
- IGMPv2 SSM mapping 132
- Configuration requirements 135
- Changing the IGMP mode 136
- Modifying the query interval 137
- Modifying the age interval 137
- Filtering multicast groups 137
- PIM SM traffic snooping 138
- Configuration Notes 142
- Application example 142
- Multicast Traffic Forwarding 143
- IP Multicast CPU Protection 146
- Verifying CPU protection 147
- Static IGMP membership 148
- Brocade(config)# vlan 100 150
- Clearing IGMP group flows 155
- Commands 156
- Release Command History 157
- IPv6 PIM Sparse 163
- PIM Sparse router types 164
- RP paths and SPT paths 165
- Configuring PIM Sparse 165
- IPv6 PIM-Sparse mode 166
- Configuring BSRs 166
- Configuring candidate RP 168
- Statically specifying the RP 168
- Embedded Rendezvous Point 169
- • Default route from the mRTM 171
- • Default route from the uRTM 171
- Setting the inactivity timer 174
- Changing the hello timer 174
- Configuring a DR priority 175
- Configuring PMRI 176
- Displaying hardware-drop 176
- Displaying BSR information 180
- Displaying the RP set list 183
- Displaying IPv6 PIM RPF 187
- Displaying IPv6 PIM counters 187
- Configuring PIM Anycast RP 192
- Enabling MLDv2 194
- Setting the robustness 197
- Setting the version 197
- Specifying a port version 197
- Displaying MLD information 198
- • The port ID 200
- • The multicast protocol used 200
- Displaying MLD settings 201
- Displaying static MLD groups 202
- Displaying MLD traffic 202
- Clearing IPv6 MLD traffic 203
- Configuring IPv6 MLD snooping 205
- Changing the MLD mode 205
- PIM-SM traffic snooping 206
- Application examples 207
- Setting the MLD version 210
Relacionado con productos y manuales para Accesorios De Computador Brocade Multi-Service IronWare Multicast Configuration Gui
Accesorios De Computador Brocade NetIron CER 2000 Series Hardware Guide (Supporting Manual de usuario
(110 paginas)
(110 paginas)
Accesorios De Computador Brocade Multi-Service IronWare Routing Configuration Guide Manual de usuario
(846 paginas)
(846 paginas)
Accesorios De Computador Brocade ICX 6610 Stackable Switch Hardware Installation Gu Manual de usuario
(108 paginas)
(108 paginas)
Accesorios De Computador Brocade ICX 6450 Stackable Switches Hardware Installation Manual de usuario
(116 paginas)
(116 paginas)
Accesorios De Computador Brocade Multi-Service IronWare Administration Guide (Suppo Manual de usuario
(432 paginas)
(432 paginas)
Accesorios De Computador Brocade Converged 10GbE Switch Module for IBM BladeCenter Manual de usuario
(12 paginas)
(12 paginas)
Accesorios De Computador Brocade ICX 6430-C Compact Switch Hardware Installation Gu Manual de usuario
(64 paginas)
(64 paginas)
Accesorios De Computador Brocade ICX 6450-C Compact Switch Hardware Installation Gu Manual de usuario
(64 paginas)
(64 paginas)
Accesorios De Computador Brocade Multi-Service IronWare Multiprotocol Label Switch Manual de usuario
(852 paginas)
(852 paginas)
Accesorios De Computador Brocade FCoE Switch Module for IBM BladeCenter Installatio Manual de usuario
(76 paginas)
(76 paginas)
Accesorios De Computador Brocade FastIron WS Hardware Installation Guide Manual de usuario
(74 paginas)
(74 paginas)
Accesorios De Computador Brocade TurboIron 24X Series Hardware Installation Guide Manual de usuario
(84 paginas)
(84 paginas)
Accesorios De Computador Brocade FastIron SX Series Chassis Hardware Installation G Manual de usuario
(192 paginas)
(192 paginas)
Accesorios De Computador Brocade Access Gateway Administrator's Guide (Support Manual de usuario
(0 paginas)
(0 paginas)
Accesorios De Computador Brocade Encryption Switch Hardware Reference Manual (Suppo Manual de usuario
(60 paginas)
(60 paginas)
Accesorios De Computador Brocade Encryption Switch QuickStart Guide (Supporting Fab Manual de usuario
(20 paginas)
(20 paginas)
Accesorios De Computador Brocade Unified IP MIB Reference (Supporting FastIron Rele Manual de usuario
(768 paginas)
(768 paginas)
Accesorios De Computador Brocade TurboIron 24X Series Configuration Guide Manual de usuario
(111 paginas)
(111 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales